至順電子材料有限公司

SPECIFICATIONS

Tact Switch

Common Specifications

1. Rating : 50mA 12V DC (Resistive Load)
2. Electrical Performance
Item	Test Condition	Performance
Contact Resistance	1A 5V DC	As per Individual Specifications
Insulation Resistance	100V DC for 1 minute	100MΩMin
Withstanding Voltage	250V AC for 1 minute	Shall be free from Dielectric Breakage

3. Mechanical Performance
Item	Test Condition	Performance
Operating Force		As per Individual Specifications
Stop Strength	3kgf for c seconds	No Deformation and Mechanical Problem Found
Bounce	The Key Shall be Struck Lightly at it's Center at a Uniform Cycling Rate of 3Operations Per Second	As per Individual Specifications

4. Endurance
Item	Test Condition	Performance
Life Test	2-3 Cycles/Second with 5V DC 5mA Resistive Load Cycles of Operation:As per Individual Specifications.	‧Contact Resitance : As per Individual Specifications ‧Operating Force : ±30%Initial Value ‧Insulation Resistance : 10MΩ Min
Dry Heat Proof	80℃ ± 2℃ for 96 Hours After Test. Kept in Normal Condition for 30 Min.	Equality to Initial Specifications
Moisture Resistance	60℃ ± 2℃ 90~95%RH for Hours After Test. Kept in Normal Condition for 30 Minutes.	Equality to Initial Specifications
Cold Proof	-30℃ for 96 Hours After Test. Kept in Normal Condition for 30 Minutes.	Equality to Initial Specifications

5. Solder Heat Resistance & Auto Soldering:255℃ for 5 Seconds
6. Explanation of Timing
Item	Explanation	Figure
Operation Force	It refers to the maximum load at the time of switching over of the contacts.(Point A in the figure)
Return Force	It refers to the returning force of the stem after its full travel when pushed out.(Point B in the Figure)
Click (tactile Feedback)	It refers to the feeling indicated on the inversion portion in the operating force us. Travel diagram shown en the figure. The greater this inversion part is, the clearer it is to the operator that the switch is moved.
Travel	It refers to the distance of travel of the operating part before the contacts is changed over. Generally, it is about 0.3mm in mechanical contact.
Bounce	This refers to the state of repeating the contact opening or closing momentarily at the time of the changeover of the swich to ON or OFF longer duration of this state may cause malfunction of the signal

Detector Switch

Common Specifications

1. Rating : AS per Individual Specifications
2. Electrical Performance
Item	Test Condition	Performance
Contact Resistance	1A 5V DC	As per Individual Specifications
Insulation Resistance	500V DC for 1 minute	100MΩ Min
Withstanding Voltage	500V AC for 1 minute	Shall be free from Dielectric Breakage

3. Mechanical Performance
Item	Test Condition	Performance
Operating Force		As per Individual Specifications
Terminal Strength	500gf for 1minute	No Terminal Rejection and Insulator Breakage

4. Endurance
Item	Test Condition	Performance
Life Test	10,000 Cycle Operations (15~20Cycles/Minute) Without Load	‧Contact Resistance : PS Series : 100MΩ Max ‧Operating Force : +10,-30%Initial Value ‧insulation Resistance :10MΩ Min ‧Withstand Voltage : 500V AC for 1minute
Cold Proof	-20±3℃ for 96 Hours After Test, Kept in Normal Condition for 1Hours, to be Measured within 1Hour.	‧Contact Resistance : 200MΩMax ‧Operatif Force : +10, -30%Initial Value ‧Insulation Resistance : 10MΩ Min. ‧Withstanding Voltage : 500V AC for 1 Minute
Dry Heat Proof	80±2℃ for 96 hours After Test, kept in Normal Condition for 1Hour, to be Measured within 1Hour.

5. Explanation of Changeover Timing

Shorting

Non-shorting

Switching action is accomplished after electrical connections have been made once across terminals during circuit selection.(Terminals① ,② and ③electrically connected once)

Electrical connections are turned off once across terminals during circuit selection.
(Terminals① ,② and ③ are electrically turned off once)

① ② ③

↓ ↓ ↓

▶

Stationary position

During switching

After switching

Stationary position

During switching

After switching

Push Switch

Common Specifications

1. Rating : AS per Individual Specifications
2. Electrical Performance
Item	Test Condition	Performance
Contact Resistance	1A 5V DC	As per Individual Specifications
Insulation Resistance	500V DC for 1 minute	100MΩ Min
Withstanding Voltage	500V AC for 1 minute	Shall be free from Dielectric Breakage

3. Mechanical Performance
Item	Test Condition	Performance
Operating Force		As per Individual Specifications
Terminal Strength	500gf for 1minute	No Terminal Rejection and Insulator Breakage

4. Endurance
Item	Test Condition	Performance
Life Test	10,000 Cycle Operations (15~20Cycles/Minute) Without Load	‧Contact Resistance : PS Series : 100 Max ‧Operating Force : +10,-30%Initial Value ‧insulation Resistance :10MΩ Min ‧Withstand Voltage : 250V AC for 1minute
Cold Proof	-20±3℃ for 96 Hours After Test, Kept in Normal Condition for 1Hours, to be Measured within 1Hour.	‧Contact Resistance : 200MΩ Max ‧Operatif Force : +10, -30%Initial Value ‧Insulation Resistance : 10MΩ Min. ‧Withstanding Voltage : 500V AC for 1 Minute
Dry Heat Proof	80±2℃ for 96 hours After Test, kept in Normal Condition for 1Hour, to be Measured within 1Hour.

5. Explanation of Changeover Timing

Shorting

Non-shorting

Switching action is accomplished after electrical connections have been made once across terminals during circuit selection.(Terminals① ,② and ③electrically connected once)

Electrical connections are turned off once across terminals during circuit selection.
(Terminals① ,② and ③ are electrically turned off once)

① ② ③

↓ ↓ ↓

▶

Stationary position

During switching

After switching

Stationary position

During switching

After switching

Slide Switch

Common Specifications

1. Rating : AS per Individual Specifications
2. Electrical Performance
Item	Test Condition	Performance
Contact Resistance	1mA 5V DC	20MΩ Max
Insulation Resistance	500V DC for 1 minute	100MΩMin
Withstanding Voltage	500V AC for 1 minute	Shall be free from Dielectric Breakage

3. Mechanical Performance
Item	Test Condition	Performance
Operating Force		As per Individual Specifications
Stop Strength	500gf for 1minute	No Terminal Rejectionand Insulator Breakage
Lever strength	2Kgf for 15 seconds	No Deformation and Mechanical Problem Found

4. Endurance
Item	Test Condition	Performance
Life Test	10,000 Cycle Operations (15~20Cycles/Minute) Without Load	‧Contact Resistance : 100MΩMax ‧Operating Force : ±10%Initial Value -30 ‧insulation Resistance :10MΩ Min ‧Withstand Voltage : 250V AC for 1minute
Cold Test	-20±3℃ for 48±5 Hours After Test, Kept in Normal Condition for 1Hours, to be Measured within 1Hour.	Equality to Initial Specifications
Dry Heat Proof	80±2℃ for 48±55 hours After Test, kept in Normal Condition for 1Hour, to be Measured within 1Hour.	Equality to Initial Specifications

5. Solder Heat Resistance : Auto Soldering : 260° ± 5℃/3Seconds
Manual Soldering : 350° ±5℃/3Seconds

6. Explanation of Changeover Timing

Shorting

Non-shorting

Switching action is accomplished after electrical connections have been made once across terminals during circuit selection.(Terminals① ,② and ③electrically connected once)

Electrical connections are turned off once across terminals during circuit selection.
(Terminals① ,② and ③ are electrically turned off once)

① ② ③

↓ ↓ ↓

▶

Stationary position

During switching

After switching

Stationary position

During switching

After switching

Hook Switch

Common Specifications

1. Rating : 200mA 48V DC (Resistive Load)
2. Electrical Performance
Item	Test Condition	Performance
Contact Resistance	1A 5V DC	50MΩ Max
Insulation Resistance	500V DC for 1 minute	100MΩ Min
Withstanding Voltage	500V AC for 1 minute	Not Breaking Insulation

3. Mechanical Performance
Item	Test Condition	Performance
Operating Force		As per Individual Specifications
Terminal Strength	300gf for 1minute	No Terminal Rejection and Insulator Material Breakage
Lever strength	1Kg for Force for 15seconds	There shall not be any Troubles as Deviation and Bending

4. Mechanical Performance
Item	Test Condition	Performance
Life Test	300,000 Cycle Without Load 100,000 Cycle With 0.2A 48V DC Pesistive Load	‧Contact Resistance : 1Ω Max ‧Operating Force : ±10,-30%Initial Value ‧insulation Resistance :10MΩ Min ‧Withstand Voltage : 500V AC for 1minute
Cold Test	20±2℃ for 96 Hours After Test, Kept in Normal Condition for 1Hours, to be Measured within 1Hour.	‧Contact Resistance : 200mΩ Max ‧Operating Force : ±10,-30%Initial Value ‧insulation Resistance :10MΩMin ‧Withstand Voltage : 500V AC for 1minute
Dry Heat Proof	85±2℃ for 96 hours After Test, kept in Normal Condition for 1Hour, to be Measured within 1Hour.
Moisture Resistance	40±2℃ 90~95 RH for 96 hours After Test, kept in Normal Condition for 1Hour, to be Measured within 1Hour.

5. Solder Heat Resistance : Auto Soldering : 260℃± 5℃/3 Seconds
Manual Soldering : 350℃±5℃/3 Seconds

Stereo Jack

Common Specifications

1. Construction
NO	Item	Performance
1-1	Dimension	Shape and dimensions subject to attached chart requlation
1-2	Appearance	Every part should be finished not to exist rust flaw crack and bad plating

2. Electrical Performance
NO	Item	Test Condition	Performance
3-1	Contact resistance	DC 5V, 1A by voltage droop method	30mΩ max.
3-2	Insulation resistance	DC 500V for 1 minute	100mΩ min
3-3	Withstand voltage	AC 500V (50Hz or 60Hz)fir 1 minute	No breakdown

3. Mechanical Performance
NO	Item	Test Condition	Performance
4-1	Insulation force		As per Individual Specifications
4-2	Extraction force		As per Individual Specifications
4-3	Terminal strength	500gf for 1 minute	No Terminal Rejection and Insulator Breakage
4-4	Lever strength	1kgf for 15 seconds	no mechanical and electrical problem

4. Endurance
NO	Item	Test Condition	Performance
5-1	Operating life	5,000 cycles (15~20 cycles/min)	Contact Resistance : 50mΩ Max
		unloading	Insulation resitance : 100mΩ min.
			Withstand voltage : AC 500V for 1 minute, no breakdown
			Insertion or extraction force:
			Within+10%~-30% of initial force

5. Soldering
NO	Item	Performance
7-1	Automatic soldering	260℃±5℃ 3sec. max
7-2	Manual soldering	350℃±5℃ 3sec. max

Dc Jack

Common Specifications

1. Construction
NO	Item	Performance
1-1	Dimension	Shape and dimensions subject to attached chart requlation
1-2	Appearance	Every part should be finished not to exist rust flaw crack and bad plating

2. Rating Performance
3. Electrical Performance
NO	Item	Test Condition	Performance
3-1	Contact resistance	DC 5V, 1A by voltage droop method	30mΩ max.
3-2	Insulation resistance	DC 500V for 1 minute	100mΩ min
3-3	Withstand voltage	AC 500V (50Hz or 60Hz)fir 1 minute	No breakdown

4. Mechanical Performance
NO	Item	Test Condition	Performance
4-1	Insulation force		As per Individual Specifications
4-2	Extraction force		As per Individual Specifications
4-3	Terminal strength	500gf for 1 minute	No Terminal Rejection and Insulator Breakage
4-4	Lever strength	1 kgf for 15 seconds	no mechanical and electrical problem

5. Endurance
NO	Item	Test Condition	Performance
5-1	Operating life	5,000 cycles (15~20 cycles/min)	Contact Resistance : 50mΩ Max
		unloading	Insulation resitance : 100mΩ min.
			Withstand voltage : AC 500V for 1 minute, no breakdown
			Insertion or extraction force:
			Within+10%~-30% of initial force

6. Soldering
NO	Item	Performance
6-1	Being Kept in the condition at -20℃±3℃ for 48±5hours, then in normal condition for 1hour, to be measured within 1 hour Waterdrops shall be removed	Equality to specification of No. 5-1
6-2	Being kept in the condition at80℃±2℃ for 48±5hours, then in normal condition for 1hour, to be measured within 1 hour	Equality to specification of No. 5-1

7. Soldering
NO	Item	Performance
7-1	Automatic soldering	260℃±5℃ 3sec. max
7-2	Manual soldering	350℃±5℃ 3sec. max

DIP Switch

Common Specifications

至順電子材料有限公司

好友分享